Finding your suitable arduino kit cnc is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best arduino kit cnc including detail information and customer reviews. Let’s find out which is your favorite one.
Best arduino kit cnc
1. Eiechip CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver
Feature
3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module.The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors.
Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors
This shield can make quick work for managing stepper motors in your project
Description
CNC Shield Board:1>PWM Spindle and direction pins
2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
3>2 x End stops for each axis (6 in total)
4>Coolant enable
5>Uses removable A4988 or DRV8825 compatible stepper drivers
6>Compact design
7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
UNO R3 Board for Arduino:
1>MCU: ATmega328
2>USB interface: ATmega16U2
3>Operating voltage: 5V
4>Digital I/O pins: 14 (including 6 with PWM capability)
5>Analog input pins: 6
6>I-I/O pin output current: 40mA max
7>3.3V output current: 150mA max
8>Flash memory: 32kB (0.5kB used by bootloader- included)
9>Static RAM (SRAM): 2kB
10>EEPROM: 1kB
11>Clock speed: 16MHz
LCD 2004 Smart Controller
Easy connect it to your Ramps board using the "smart adapter" included.
After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.
Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.
2. Arduino CNC Kit w/ UNO + Shield+ Stepper motors DRV8825 Endstop A4988 GRBL
Feature
US ship arrived 4-10 days.The kit contains following items: 1x UNO R3+CH340G Board.it's compatible with all arduino software and hardware
1X 40" Gold plated/shielded USB cable w/noise suppressor. Essential for stable connection and printing.
it's compatible with all arduino software and hardware. 4x Aluminum heatsink w/ tape backing
stepper motors 3X Mechanical endstop switch w/ 40" cable 4x DRV8825 stepper motor driver (upgraded from A4988, 2.5 A max current/phase.
Description
The kit contains following items: 1x UNO R3+CH340G Board.it's compatible with all arduino software and hardware. 1X 40" Gold plated/shielded USB cable w/noise suppressor. Essential for stable connection and printing. 1x CNC shield 3X 1.5A 0.42 N.m stepper motors 3X Mechanical endstop switch w/ 40" cable 4x DRV8825 stepper motor driver (upgraded from A4988, 2.5 A max current/phase. it's compatible with all arduino software and hardware. 4x Aluminum heatsink w/ tape backing3. Quimat Arduino CNC Shield Contoller Kits for 3D Printer,CNC Shield V3.0 + UNO R3 Board + Nema 17 Stepper Motor + A4988 Stepper Motor Driver + Heat Sinks,Perfectly Compatible with GRBL
Feature
CNC Shield V3.0 Features - Latest Version 3.0, GRBL 0.8c compatible, 4 Axis supported and 2 end stops for each axis.Compact design - Stepper motors can be connected with 4 pin molex connectors or soldered in place.
Stepper Drivers - Uses removable Pololu A4988 compatible stepper drivers, jumpers to set the Micro-Stepping for the stepper drivers
Stepping Motor Included - Nema 17 model, holding torque of 26Ncm(36.8oz.in), 12V/0.4A and 1.8 deg.step angle(200 steps/rev)
Technical support - Our technical support team is on standby to provide solutions to your questions, please feel free to contact us.
Description
CNC Shield V3.0 features: Latest Arduino CNC Shield Version 3.0. GRBL 0.8c compatible.(Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support(X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis(6 in total), Spindle enable and direction Coolant enable Stepper drivers Uses removable Pololu A4988 compatible stepper drivers. Jumpers to set the Micro-Stepping for the stepper drivers. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Stepping Motor The most popular Nema 17 model with 1.8 deg. step angle (200 steps/revolution) 0.4A rated current/phase, allowing for a holding torque of 26Ncm(36.8oz.in) Connection:Black(A+), Green(A-), Red(B+), Blue(B-) Stepping Motor Specification: * Cable length: 11.8 inches * Phase Resistance: 30ohms * Inductance: 37mH+/-20%(1KHz) * Frame Size: 42 x 42mm * Body Length: 34mm * Shaft Diameter: 5mm * Front Shaft Length: 20mm * D-cut Length: 15mm * Number of Leads: 4 * Lead Length: 300mm * Weight: 230g Kit list: 1x CNC Shield V3.0 1x Keyestudio UNO R3 board 4x A4988 driver 1x USB cable 1x Nema 17 stepping motor4. Professional CNC Kit for arduino, kuman GRBL CNC Shield +UNO R3 Board + RAMPS 1.4 Mechanical Switch Endstop + DRV8825 A4988 GRBL Stepper Motor Driver with Heat Sink + Nema 17 Stepper Motor
Feature
Latest CH340G CNC Shield expansion board Version 3.0 for ArduinoKuman UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable
4pcs DRV8825 Stepper Motor Driver with heat sinks
3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with mounting Bracket Kit DIY CNC Robot with 3pcs Mounting Bracket and 12 pcs M3 Screws
3pcs Endstop Mechanical Limit Switches for RAMPS 1.4 with 3Pin 70cm Cable
Description
CNC Shield Board:Latest CNC Shield Version 3.0 for arduino
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC
DRV8825 Stepper Motor Driver:
Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It's not arduino official board but it's compatible with all arduino software and hardware)
Nema 17 Stepper motor Specification:
Model No.:17HD48002H-22B
Step Angle: 1.8 deg.
Holding Torque: 59Ncm(84 oz.in)
Rated Current/phase: 1.7A
Frame Size: 41 x 41mm
Body Length: 47mm
Shaft Diameter: 5mm
Shaft Length: 22mm
Weight: 380g
Mechanical Endstop Connection description:
Red line connect VCC (ramps of +)
black wire connect the GND (ramps of -)
Green Line connect SIGNAL (ramps in s)
Tips: Under normal circumstances, the system must be configured to at least three mechanical switches.
Advantage: Easy to install, the more common used styles
Length of Cable: 70 cm
Package Contents:
1 x CNC Shield Board
1 x Kuman UNO R3 Board
4 x DRV8825 Stepper Motor Driver
4 x Aluminum heatsink w/ 3M tape backing
3 x Nema 17 stepper motor 1.7 A (with bracket and screw)
3 x Nema 17 Stepper Motor Mounting Bracket
12x M3 Screws for bracket of stepper motor
3 x Mechanical Switch Endstop
3 x 3Pin 70cm Cable
1 x 1.5m USB cable for R3 Board
5. Gowoops 3D Printer kit CNC Shield V3 Expansion Board + UNO R3 Board + 4PCS DRV8825 Step Motor Driver with Heatsinks for Arduino
Feature
Latest Arduino CNC Shield Version 3.0, CNC Capacitance: 50V 100uFPWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC
Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step).
The DRV8825 operates from 8.2 - 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling
Description
Arduino CNC Shield V3.0 Installation Guide:http://osoyoo.com/?p=4783
CNC Shield Board: (learn more information, pls go to the ASIN: B0157ZZ28M)
Please note that this is an unassembled kit and Basic soldering skills are needed
Arduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader - included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHz
DRV8825 Stepper Motor Driver Module:
Simple step and direction control interface
Can interface directly with 3.3 V and 5 V systems
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
Short-to-ground and shorted-load protection
4-layer, 2 oz copper PCB for improved heat dissipation
Exposed solder-able ground pad below the driver IC on the bottom of the PCB
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates
45 V maximum supply voltage
Built-in regulator (no external logic voltage supply needed)
Module size, pinout, and interface match those of our A4988 stepper motor driver The max running currency: 2.5A
Size: 1.5mmX2mm
Package includes:
1x CNC Shield Board
1x Arduino UNO R3 Board
4x DRV8825 Stepper Motor Driver
4x Aluminum Heatsink
6. KEYESTUDIO CNC Kit /V0.9A Shield +4988 Driver with Heat Sink for Arduino
Feature
MicroprocessorMEGA328pWith simple stepper and direction control interface.
Five different step modes: full, half, 1/4, 1/8 and 1/16 step modes.
Adjustable potentiometer used to adjust the max current output to gain higher step rate.
Supporting Machine StructureCNC, laser engraving machine, writing robots
Description
IntroductionThis kit mainly includes a keyestudio CNC V0.9A, three A4988 driver modules with heat sink and a USB cable.
Keyestudio CNC GRBL V0.9 is a main board developed by Keyestudio for CNC, laser engraving machine, writing robots and other robots. It has complete interfaces with cost-effective and can be driven via external connection, suitable for DIY and factory use.
The A4988 module is a DMOS microstepping driver with converter and overcurrent protection, which can operate a bipolar stepper motor in full, half, 1/4, 1/8 and 1/16 step modes, with output-driven performance up to 35 V and 2A. The A4988 also includes a fixed off-time current regulator that operates in slow or mixed-decay modes.
Specification of CNC V0.9A
MicroprocessorMEGA328p Input VoltageDC 12V Supporting File FormatGcode Supporting Machine StructureCNC, laser engraving machine, writing robot
Features of A4988 Driver
With simple stepper and direction control interface.
Five different step modes: full, half, 1/4, 1/8 and 1/16 step modes.
Adjustable potentiometer used to adjust the max current output to gain higher step rate.
Automatic decay mode detection/selection.
Overheat closed circuit, under-voltage lockout, cross-current protection.
Ground short-circuit protection and load short-circuit protection.
7. 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.4 with Upgraded Mosfet + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap (14 Items)
Feature
3D Printer Controller Kit Mega 2560 R33D Printer Controller RAMPS 1.4 interfaces an Arduino Mega2560 board. The modular design includes a plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgradeability and expansion
LCD 12864 Graphic Smart Display Controller and the A4988 Stepper Motor Driver
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code are provided for free, just contact us by Email
Description
Difference between 2016 and 2017 Version 2016 Old MOSFET IC Model : PDF55N06 VDSS:60V ID:55A 2017 New MOSFET IC model: HM60N06 VDSS:60VID:60A, more durable and safety. Product Features: 1) Mega 2560 R3 2) 3D Printer Controller RAMPS 1.4 with high-quality MOSFET Designed to fit the entire electronics needed for a RepRap in one small package for low cost, interface with the powerful Arduino-compatible Mega platform with plenty space for expansion. 3) A4988 Stepper Motor Driver A complete micro-stepping motor driver with built-in translator for easy operation 4) LCD 12864 Graphic Smart Display Controller Contains an SD-Card reader, a rotary encoder, and a 128 x 64 dot matrix LCD display. Easy to connect it with your Ramps board using the "smart adapter" included. Package List: (1) RAMPS 1.4 x 1 (2) Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1Caution: 1.Please read the technical parameters of the board carefully before you use it; 2.Only connect the mega2560 board with the computer via USB cable while programming firmware; 3.Reversed connection of the power supply or the motor driver may cause the board burning, please confirm again before power on; 4.Only power on the Ramps 1.4 while testing the product, supply power to the mega2560 board may cause burning the board; 5.Select the appropriate load according to the board voltage/current requirement,if the work current exceeds the load of the board which may cause the board burning. If you have any questions and need any technical help, please be free to contact us, we will try our best to help you.8. keyestudio 3D Printer Cnc Kit for Arduino RAMPS 1.4 + Mega 2560 + 5x A4988 + 20x4 LCD Controller with Adapter Compatible for Arduino and RepRap
Feature
MEGA 2560 BOARD fOR ARDUINO: has more pins and uses the officialATmega16u2 and ATmega328Pwhich provide faster translate rates and more memory, allow more complex programs and projects to be doneRAMPS 1.4: It is a Mega Pololu Shield,designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion
Smart Lcd Control Panel:includes a SD card reader, a rotary encoder and a 20 * 4 LCD. When itis connected to RAMPS 1.4, with g-code design stored on the SD card, you can print your 3D designs without PC
A4988 Stepper Motor Driver: simple step and direction control interface; thermal shutdown circuit/cross current/ground fault/short circuit protection, five step modes; voltage: 3.3v and 5v; mix with slow current attenuation model etc
Qualityand Service Guarantee: all the components are well made and packaged, we will make function,voltage, current testingbefore packaging and offer professional technical support, has ROHS and CE certification
Description
1. Keyestudio Mega 2560 boardWorks as original Mega 2560, has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs, 16 MHz crystal oscillator.
2. LCD 2004 Smart Controller
Easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.
3. RAMPS 1.4
A Mega Pololu Shield
3 mosfets for heater / fan outputs and 3 thermistor circuits;
Fused at 5A for additional safety and component protection;
Heated bed control with additional 11A fuse;
Fits 5 Pololu stepper driver board;
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs;
I2C and SPI pins left available for future expansion;
All the Mosfets are hooked into PWM pins for versatility;
Servo style connectors are used to connect to the endstops, motors, and LEDs. These connectors are gold plated, rated for 3A, very compact;
SD Card add on available
LEDs indicate when heater outputs on
Option to connect 2 motors to Z for Prusa Mendel
4. A4988 stepper driver
This product is a carrier board or breakout board for Allegro's A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.
Package list
1pc Keyestudio Mega2560
1pc Lcd2004 smart Controller
1pc Ramps 1.4
5pcs A4988 stepper driver
1pcs Panel Adapter
1pcs USB 2.0 cable
9. Quimat 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.4 with Upgraded Mosfet + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap
Feature
3D Printer Controller Kit Mega 2560 R33D Printer Controller with new upgraded RAMPS 1.4,high quality MOSFET HM60N06 with up to 60A work current,more durable and safety
LCD 12864 Graphic Smart Display Controller and the A4988 Stepper Motor Driver
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code are provided for free, just contact us by Email
Description
Difference between 2016 and 2017 Version 2016 Old MOSFET IC Model : PDF55N06 VDSS:60V ID:55A 2017 New MOSFET IC model : HM60N06 VDSS:60V ID:60A,more durable and safety Product Features: 1).Mega 2560 R3 2).3D Printer Controller RAMPS 1.4 with high quality MOSFET Designed to fit the entire electronics needed for a RepRap in one small package for low cost, interface with the powerful Arduino-compatible Mega platform with plenty space for expansion. 3).A4988 Stepper Motor Driver A complete micro-stepping motor driver with built-in translator for easy operation 4).LCD 12864 Graphic Smart Display Controller Contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. Easy to connect it with your Ramps board using the "smart adapter" included. Package List: RAMPS 1.4 x 1 Mega 2560 R3 x 1 A4988 Stepper Motor Driver with Heatsink x 5 LCD 12864 Graphic Smart Display Controller x 1 Smart Adapter x 1 Cable x 2 USB Cable x 1 Note: 1.Please read the technical parameters of the board carefully before you use it 2.Only connect the mega2560 board with the computer via USB cable while programming firmware; 3.Reversed connection of the power supply or the motor driver may cause the board burning, please confirm again before power on; 4.Only power on the Ramps 1.4 while testing the product, supply power to the mega2560 board may cause burning the board; 5.Select the appropriate load according to the board voltage/current requirement,if the work current exceeds the load of the board which may cause the board burning Any questions or concerns, please feel free to contact us,we are looking forward to serving you again10. Longruner 6 x Mechanical Endstop Limit Switch with 22AWG Cable for 3D Printer Makerbot Prusa Mendel RepRap CNC Arduino Mega 2560 RAMPS 1.4 LKB01
Feature
Mechanical Endstop kit is for RepRap 3D Printers or CNC machines, it is supported by RepRap electronics, RAMPS 1.4 and by other popular RepRap boards.Customized high quality connection, using 22AWG wire, the copper wire inside is thick which can withstand 2A current, 300V voltage.
Wide insulation temperature range: The insulation temperature can reach up to 80 degrees, better than the ordinary thin copper wire.
Red line connecting VCC (ramps of +); Connect the black wire GND (ramps of -);Green Line connection SIGNAL (ramps in s).
The wire is strong and convenient for plug, can be inserted directly to use.
