If you looking for arduino holder then you are right place. We are searching for the best arduino holder on the market and analyze these products to provide you the best choice.
Best arduino holder
1. SunFounder Raspberry Pi RAB Holder Breadboard Kit with 830 Points solderless Circuit Board Raspberry Pi Holder for Arduino Uno R3, Mega 2560 & Raspberry Pi 3B+, 3 Model B, 2 Model B and 1 Model B+
Feature
The Sunfounder breadboard kit fits perfectly for a Raspberry Pi 3B+, 3 Model B, 2 Model B and 1 Model B+ , an Arduino Uno or Mega 2560The high quality RAB Holder makes everything convenient and neat.Enlarge the fun when you fix the Raspberry Pi and Arduino boards.
This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails.
Including T-shape GPIO Extension Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B+, 3 Model B, 2 Model B, 1 Model B+
Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs, ten 1k resistors, a screwdriver, and some screws.
Description
IntroductionThis RAB Holder Kit provides you all the necessary components for a simple experiment, including threads for easy screwing, slots for plugging wires, an RAB holder, nine LEDs, and ten 1K current-limiting resistors, thus you can start the experiment right away.
With this kit, you can fix your Arduino board, Raspberry Pi, and breadboard on the RAB Holder, free of careless short circuits on a metal desk or caused by some metal parts underneath. What's more, it also comes with 65pcs jumper wires with different length in various colors, therefore, you can just plug them into the control board and breadboard to build circuits, no bothering about complicated soldering.
Specifications
Size: 200 x 135 mm (7.87 x 5.31 inch)
Package Included
1 x RAB Holder
1 x 830-Point Breadboard
65 x Jumper Wire
1 x 20cm FC40 40pin Flat Rainbow Ribbon Cable
10 x 1k Resistor
1 x Screwdriver
1 x T-Extension
9 x LED (3 red, 3 yellow, and 3 green)
12 x Screws(4 x M3*6 screws ,4 x PWM2*6 screw, 4 x PWM2*4 screws)
2. UNIROI 7 in 1 RAB Holder Breadboard,Base Plate Case for Arduino Uno R3 Mega 2560, Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero W and Zero UA031 (RAB Holder)
Feature
Wider Compatibility: UNIROI Arduino Raspberry pi Breadboard Holder is widely compatible with Arduino Uno R3 Mega 2560, Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero W and Zero 400 800 Points Circuit Board.Convenient Slot Design: The RAB holder's slot location allows TF/Mini SD/HDMI/USB to be easily inserted without any hindrance.
Gift: A GPIO 40 pin reference card with wiring Pi and BCM codes for all Raspberry pi motherboard. Convenient to check the Pin corresponding for every experiment.
Portability and Practicability: Made of long-lasting polyethylene plastic, features small size and lightweight, easy to be moved, carried and fixed on the flat table, convenient for making projects.
Package list: 1 x blue RAB holder, 1 x black screwdriver, 4 x M3*6+5 screws, 4 x PWM2*6+5 screws, 4 x PWM2*4+5 screws, 3 x M2*4+3 copper nuts, 1 x GPIO reference card. ( Note: Arduino Rapsberrry pi motherboard and 400 breadboard are not included).
Description
UNIROI 7 in 1 RAB holder KitWidely compatible with Arduino UNO R3, Arduino Mega 2560, Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero W and Zero 400 800 Points Circuit Board.
Convenient Slot Design allows TF/Mini SD/HDMI/USB to be easily inserted without any hindrance.
GIFT: GPIO 40 pin reference card
A GPIO 40 pin reference card with wiring Pi and BCM codes for all Raspberry pi motherboard. Convenient to check the Pin corresponding for every experiment.
Simple Use: Only need to cut along the dotted line down and directly set on the raspberry Pi motherboard , then you can intuitive see each pin corresponding GPIO function.
Package included:
1 x blue RAB holder
1 x screwdriver
4 x M3*6+5 screws
4 x PWM2*6+5 screws
4 x PWM2*4+5 screws
3 x M2*4+3 copper nuts
1 x GPIO reference card
Note: Arduino Rapsberrry pi motherboard and 400 breadboard are not included.
3. JBtek Acrylic Transparent Base Plate & Terminal Optimizer Breadboard for Arduino UNO R3
Feature
Package includes: 1 x base plate for UNO R3, 1 x terminal optimizer breadboard, mounting screws and nutsBase plate designed for Arduino UNO R3
Description
-Package includes: 1 x base plate for UNO R3, 1 x terminal optimizer breadboard, mounting screws and nuts. -Base plate designed for Arduino UNO R3.4. UNIROI Breadboard Kit with Arduino Raspberry Pi Breadboard Holder, 14 in 1 RAB Holder Kit for Arduino UNO R3, Arduino Mega 2560, Raspberry Pi 3B+, 3B, 2B, 1B+ RPI Zero W and Zero, and Breadboard UA032
Feature
Wider Range CompatibilityThis RAB Holder is compatible with Arduino UNO R3, Arduino Mega 2560, Raspberry Pi 3B+, 3B, 2B, 1B+ RPI Zero W and Zero, and Breadboard.PortabilityUsing this holder to fix Arduino UNO R3 board, Arduino mega 2560, Raspberry Pi and Breadboard for your project, make it easier to build and carry your projects.
Slot DesignAllows HDMI cable, USB cable and TF card to be easily inserted into Raspberry Pi without any hindrance.
830 points breadboardIncludes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails, can be used to make several projects at the same time.
GiftComes with GPIO 40 pin reference card with wiring Pi and BCM codes for all Raspberry pi motherboard. Convenient to check the Pin corresponding for every experiment.
Description
UNIROI 14 in 1 Arduino Raspberry Pi Breadboard Holder Kit, help you fix Arduino UNO R3, Arduino mega 2560, Raspberry Pi and Breadboard for your project, make it easier to build and carry your projects.Wide Compatibility:
This RAB holder is compatible with Arduino UNO R3, Arduino Mega 2560 & Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero W and Zero and Breadboard.
The Using Method of GPIO Reference Card:
Only need to cut along the dotted line down and directly set on the raspberry Pi motherboard, then you can intuitive see each pin corresponding GPIO function.
Package contents:
1 x 830 points breadboard
1 x Blue breadboard holder
65 x Jumper wires
20 x Female to male DuPont wires
1 x Screwdriver
4 x M3*6+5 screws
4 x PWM2*6+5 screws
4 x PWM2*4+5 screws
3 x M2*4+3 copper nuts
3 x Red LED(5mm)
3 x Yellow LED(5mm)
3 x Green LED(5mm)
10 x 1K resistors
1 x GPIO reference card
NOTE: Arduino Rapsberrry pi motherboard are not included.
5. UNO Starter Kit for Arduino, UNIROI Complete Arduino Kit for Beginner with Detailed Tutorials, RAB Holder, Breadboard for Arduino UNO R3 Arduino Mega 2560 Arduino Nano Robot (52 Items) UA005
Feature
Free PDF tutorials with more than 20 lessons are included in CD. UNIROI Arduino Starter Kit is specially designed for Arduino beginners.RAB Holder: Fixing Arduino UNO R3, mega2560, raspberry pi and breadboard for your project, make it easier to build and carry your projects.
Upgraded Aruino UNO R3 board is based on ATMega328 chip for controlling, 100% compatible with official version Arduino. And features faster transfer rates and more memory with ATMega16U2 chip instead of ATMega8U2.
Arduino power supply module, LCD1602 module with pin header, Arduino motor and Arduino wires are included.
Gift: Resistor color card (Please add resistors when using LED to avoid over current), Raspberry Pi GPIO reference card with wiring Pi and BCM codes for all Raspberry pi motherboard. Convenient to check the Pin corresponding for your experiment.
Description
UNIROI Arduino UNO KitRAB holder: compatible with Arduino Uno R3, Mega 2560 & Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ RPI Zero W and Zero.
How to use GPIO reference card: Only need to cut along the dotted line down and directly set on the raspberry Pi motherboard, then you can intuitive see each pin corresponding GPIO function.
Package list:
1)1 x Arduino UNO R3 Board
2)1 x RAB Holder
3)1 x 3.5V/5V Arduino Power Supply module
4)1 x Prototype Extension Board
5)1 x Arduino Mini Breadboard
6)1 x 5V Stepper motor
7)1 x 2003 Stepper motor driver board
8)1 x IC 74HC595
9)2 x Vibration Sensor
10)1 x Flame Sensor
11)1 x DTH11 Temperature and Humidity Sensor
12)1 x Infrared receiver
13)3 x Photoresistor
14)10 x Arduino LED (red)
15)10 x Arduino LED (green)
16)10 x Arduino LED (blue)
17)2 x Yellow Key Switch
18)2 x Red Key Switch
19)1 x Active buzzer tone generator
20)1 x Passive buzzer piezo buzzer
21)4 x Key Cap
22)1 x Adjustable potentiometer
23)1 x HC-SR04 module
24)1 x LCD1602 Arduino display with pin header
25)1 x Remote Control
26)1 x 1 digit 7 segment tube
27)1 x 4 digit 7 segment tube
28)1 x 8x8 dot matrix
29)30 x Breadboard Jumper Wire
30)1 x 10pin DuPont line
31)1 x Thermistor module
32)1 x Large breadboard
33)1 x 9V
34)1 x Holder
35)1 x Touch sensor
36)1 x RGB LED module
37)1 x USB cable
38)10 x 220 ohm Resistance
39)10 x 330 ohm Resistance
40)10 x 1K ohm Resistance
41)10 x 10K ohm Resistance
42)1 x Resistance card
43)1 x Raspberry Pi GPIO Reference Card
44)1 x Cross Screwdriver
45)4 x M3*6+5 Screws
46)4 x PWM2*6+5 Screws
47)4 x PWM2*4+5 Screws
48)3 x M2*4+3 Screws
49)1 x CD with tutorial
50)1 x Component box
51)1 x plastic box
6. kuman Raspberry Pi Holder Breadboard Kit, 7 in 1 RAB Holder kit for Arduino Uno R3, Mega 2560 & Raspberry Pi 3 Model B, 2 Model B,1 Model B+ RPI Zero and Zero W (Raspberry Pi Holder Breadboard Kit)
Feature
This 7 in 1 RAB Holder kit is designed by Kuman for the Raspberry Pi and Arduino hobbyists, the holder is large enough for a Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W, Arduino Uno R3 or Mega 2560, and a 400 hole or 830 hole Circuit Board breadboard(Arduino rapsberrry pi motherboard and 400 breadboard are not included).Gift: GPIO 40 pin Table Card for wiring Pi and BCM codes for all RPI motherboard.
Including RPi GPIO Breakout Expansion Board and Ribbon Cable, which are special for Raspberry Pi 3 Model B, 2 Model B, 1 Model B+ and zero/ zero W.
This 830-tie/point breadboard includes an IC area of 630 points, plus two 100-point distribution strips, providing 4 power rails.
Comes with male-to-male 65pcs jumper wires, red, green, and yellow LEDs (three for each color), ten 1k resistors, a screwdriver, and some screws.
Description
Introduction:This RAB Holder Kit provides you all the necessary components for a simple experiment, including a RPi GPIO Breakout Expansion Board, a Ribbon Cable, Raspberry PI GPIO 40 pin Table Card for wiringPi and BCM codes,a breadboard, quite a lot of jumper wires, an RAB holder, nine LEDs, and ten 1K current-limiting resistors, thus you can start the experiment right away.>
The Kit offer a GPIO hole corresponding table card for you, AS NO ANY PIN MARKED on the Rasberrry Pi motherboard interface, It is not convenient for every experiment to check the Pin corresponding ,Simple Use: Only need to cut along the dotted line down and directly set on the raspberry Pi motherboard , you can intuitive see each pin corresponding GPIO function.>
With this kit, you can fix your Arduino board, Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W, and breadboard on the RAB Holder, free of careless short circuits on a metal desk or caused by some metal parts underneath. RPi GPIO Breakout Expansion Board and Ribbon Cable are for the Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W. What's more, it also comes with 65pcs jumper wires with different length in various colors, therefore, you can just plug them into the control board and breadboard to build circuits, no bothering about complicated soldering.>
>
Specifications:
RAB Holder Size: 202.7 x 136.5 mm (7.98 x 5.37 inch)
Package Included:
1 x RAB Holder
1 x GPIO 40P Breakout Board For Raspberry Pi 3B/ 2B/ 1B+/ Zero/ Zero W
1 x 20cm FC40 40pin Flat Rainbow Ribbon Cable
1 x GPIO 40 pin Table Card for all Raspberry PI versions
1 x 830-Point Breadboard
65 x Jumper Wire
10 x 1k Resistor
9 x LED (3 red, 3 yellow, and 3 green)
1 x Screwdriver
4 x M3*6 screws ,4 x PWM2*6 screw, 4 x PWM2*4 screws, 3 x Screw copper nuts
7. Gikfun 9v Battery Holder with ON/OFF Switch for Arduino (Pack of 2PCS) EK2107x2
Feature
9v Battery Holder with ON/OFF Switch 9 Volt Box Pack Power Toggle for ArduinoPack of 2pcs
Description
2pcs 9V battery With cover and ON/OFF switch8. Smraza Ultimate UNO Project Starter Kit with Breadboard Holder,DC Motor and Detailed Tutorial for Arduino Uno R3 Mega2560 NANO
Feature
Ultimate Uno Starter Kit for Arduino UNO, Mega - Includes more common use components what you need for starting with Arduino projects.Easy to operate - With easy set-up breadboard holder makes a stable base for you to easy make electrical circuits connection.
Flexibly combination of Projects - All parts can be combined into 16 lessons, flexibly used 5V relay, LM35 temperature sensor and DC MOTOR.
Detailed tutorial - Provide CD disk PDF instruction, Software, libraries and Sample code for professional engineer or students to learn DIY Arduino projects.
Quick-response technical support - If you need any help, please contact us by Amazon.
Description
This ultimate Starter kit design for Arduino Uno includes enough components to lead you start making your own Arduino Projects. Arduino is based on C/C++ programming language so you can walk through the basics to start with Arduino. We will provide detailed tutorials in the CD and you will learn the basics of Electrical Circuits and make more funny projects by hands-on way.Package Included:
1) UNO R3 Controller Board x1
2) Breadboard Holder x1
3) 400 tie-points Breadboard x1
4) Servo Motor x1
5) 5V Relay x1
6) IC 74HC595 x1
7) 5V DC Motor x1
8) Precision Potentiometer x1
9) Active Buzzer x1
10) 2N3904Transistors x2
11) 1N4148 Diodes x2
12) TMP36 Temp Sensor x1
13) Photoresistor x2
14) Red LEDs x5
15) Green LEDs x5
16) Yellow LED x5
17) Blue LED x5
18) RGB LED x1
19) 12mm Buttons(large) x2
20) 9V Battery adapter x1
21) USB Cable x1
22) 65*Jumper Wire x1
23) Resistor (330R) x50
24) Resistor (10K) x50
25) CD x1
About Smraza:
We are a leading manufacturer of electronic components for Arduino and Raspberry Pi. We have a professional engineering team dedicated to providing tutorials and support to help you get started.
If you have any technical questions, please feel free to contact our support staff via Amazon.
9. Transparent Clear Acrylic Breadboard Holder Base Plate for Arduino UNO R3 Prototyping Platform Terminal Optimizer
Feature
This base plate is for Arduino UNO R3 surface mount device prototyping & experimental small projects.Very convenient having the Arduino and a small breadboard together on a stable platform.Helps to keep peripheral components & wiring straight and neat during developmentAcrylic Arduino mouting plate was nicely cut! Protected from scratches by protective film. Peel-off the paper and it is transparent underneath
Great UNO base with mini breadboard. Great size fits the control well and sturdy thickness let you put down your boards without fear of static damage
The acrylic platform mounting base are great.It makes it much more convenient to work with your Arduino
Simple. Keeps everything together.Provides a quick and easy method for keeping hardware neat and tidy
Description
What a fantastic little base plate for your Arduino UNO!!This is a very nice platform for experimenting with an Arduino UNO. It went together in minutes and everything is secure and stable.
The 400 points breadboard that comes with this base is good for most basic sketches. Also, the little rubber feet for the bottom of it are a nice touch. Makes it easy to prototype an Arduino project.
Well made and simple to mount the board
Description:
This clear acrylic platform is excellent for keeping your Uno and Breadboard in place whilst you work on it.The platform has mounting holes for the Uno R3 and comes with relevant screws and mounting pads for the underside. You then simply peel off the backing of your breadboard(Included)and fix it in place
Features:
A very neat transparent experimental platform base plate for Arduino UNO R3 board fixation.
Breadboard 400 tie-point can be sticked next to UNO R3 board for ease of student experiment.
Great way to keep Arduino projects all in one place, and easy to move around without taking it apart
Comes with anti slip silicon rubber feet.
Package Includes
1 x Acrylic plate- transparent
1 x 400 point breadboard
4 x Installation screws standoff set
4 x Gel Pads(Silicone rubber foot)
Note:Much better to keep everything loose until you get all the screws on!Or it will seem as though the holes are miss aligned.This means that some of the screws connected to the board need to be shifted a bit so that can fit into the Arduino.
2.The plastic and the breadboard are almost exactly the same size. Please line the breadboard up with the edges perfectly.Be careful mounting the breadboard the double sided tape is super sticky
10. Arduino and Breadboard Holder
