When you looking for ramps 1.4 with drivers, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable ramps 1.4 with drivers is not an easy task. In this post, we show you how to find the right ramps 1.4 with drivers along with our top-rated reviews. Please check out our suggestions to find the best ramps 1.4 with drivers for you.
Best ramps 1.4 with drivers
1. Eiechip CNC 3D Printer Kit for Arduino Mega 2560 R3 + RAMPS 1.4 Controller + LCD 2004 + 6X Limit Switch Endstop + 5 A4988 Stepper Driver
Feature
3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module.The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors.
Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors
This shield can make quick work for managing stepper motors in your project
Description
CNC Shield Board:1>PWM Spindle and direction pins
2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
3>2 x End stops for each axis (6 in total)
4>Coolant enable
5>Uses removable A4988 or DRV8825 compatible stepper drivers
6>Compact design
7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
UNO R3 Board for Arduino:
1>MCU: ATmega328
2>USB interface: ATmega16U2
3>Operating voltage: 5V
4>Digital I/O pins: 14 (including 6 with PWM capability)
5>Analog input pins: 6
6>I-I/O pin output current: 40mA max
7>3.3V output current: 150mA max
8>Flash memory: 32kB (0.5kB used by bootloader- included)
9>Static RAM (SRAM): 2kB
10>EEPROM: 1kB
11>Clock speed: 16MHz
LCD 2004 Smart Controller
Easy connect it to your Ramps board using the "smart adapter" included.
After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.
Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.
2. 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits + RAMPS 1.4 with Upgraded Mosfet + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap (14 Items)
Feature
3D Printer Controller Kit Mega 2560 R33D Printer Controller RAMPS 1.4 interfaces an Arduino Mega2560 board. The modular design includes a plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgradeability and expansion
LCD 12864 Graphic Smart Display Controller and the A4988 Stepper Motor Driver
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code are provided for free, just contact us by Email
Description
Difference between 2016 and 2017 Version 2016 Old MOSFET IC Model : PDF55N06 VDSS:60V ID:55A 2017 New MOSFET IC model: HM60N06 VDSS:60VID:60A, more durable and safety. Product Features: 1) Mega 2560 R3 2) 3D Printer Controller RAMPS 1.4 with high-quality MOSFET Designed to fit the entire electronics needed for a RepRap in one small package for low cost, interface with the powerful Arduino-compatible Mega platform with plenty space for expansion. 3) A4988 Stepper Motor Driver A complete micro-stepping motor driver with built-in translator for easy operation 4) LCD 12864 Graphic Smart Display Controller Contains an SD-Card reader, a rotary encoder, and a 128 x 64 dot matrix LCD display. Easy to connect it with your Ramps board using the "smart adapter" included. Package List: (1) RAMPS 1.4 x 1 (2) Mega 2560 R3 x 1 (3) A4988 Stepper Motor Driver with Heatsink x 5 (4) LCD 12864 Graphic Smart Display Controller x 1 (5) Smart Adapter x 1 (6) Cable x 2 (7) USB Cable x 1Caution: 1.Please read the technical parameters of the board carefully before you use it; 2.Only connect the mega2560 board with the computer via USB cable while programming firmware; 3.Reversed connection of the power supply or the motor driver may cause the board burning, please confirm again before power on; 4.Only power on the Ramps 1.4 while testing the product, supply power to the mega2560 board may cause burning the board; 5.Select the appropriate load according to the board voltage/current requirement,if the work current exceeds the load of the board which may cause the board burning. If you have any questions and need any technical help, please be free to contact us, we will try our best to help you.3. KINGPRINT Ramps 1.6 Expansion Control Panel with Heatsink Upgraded Ramps 1.4/1.5 for 3D Printer Board
Feature
RAMPS 1.6 interface board with new, more powerful SMT MOSFET drivers (up to 218W)Improved heat dissipation with new heat sink
3 heater / fan PWM controlled MOSFET outputs with 11A fuse protection 3 thermistor inputs
I2C and SPI for future expansion to LCD and other components
Description
Product features1. Supports up to 5 motor drivers with the standard A4988 / DRV8825 Pololu interface
2. Simple and convenient Connection, larger power than Ramps 1.5/1.4, Better Heat Dissipation with heat sink
3.The features of multiple extended interface and replaceable parts make RAMPS1.6 become a control board with powerful upgrade capability and scalable modularity.
4. 5A additional security and component protection fusion.
Please kindly note
1. The heat sink has to be installed when you use this board
2. Don't connect up with the board live (powered on) (except SD or USB)
3. Please press the RESET button or remove power in case of emergency
Package include
1 x Ramps1.6
1 x Heat sink
4. OSOYOO 3D Printer Kit with RAMPS 1.4 Controller + Mega 2560 board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter For Arduino RepRap
Feature
3D printer Kit guide: 3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf3D Printer Controller RAMPS 1.4 interfaces an Arduino Mega2560 board. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion
With LCD 12864, you can easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
It is designed to fit the entire electronics needed for a RepRap in one small package for low cost
We are professional factory on making all electronics components based on Arduino and Raspberry Pi. And we also have processional engineer team to offer you tutorials which you can start from beginning. all documents (including code)
Description
3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf
Caution:
1) The max power supply for these ramps is 12V and the max watts is about 180W. The max watts for the hotbed is about 100W and the max temperature is just 50 degree Celsius.
2) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) .
3) Always double check power wire is properly installed. If you do not follow above move, you may damage the control board and your 3D printer.
4) Pls confirm the A4988 driver install correctly on Ramps1.4 board.
5) The endstop pins are Signal-GND-VCC, instead of VCC-Signal-GND like the rest of RepRaps boards. Make sure to wire them correctly. This is done to allow squeezing fatter traces on the printable board.
6) Don't secure Arduino/Ramps with conductive screws through both mounting holes. The screw may cut into the positive trace creating a HIGH current short.
7) Test all electronics thoroughly before placing into service.
8) Do not leave power supplied to electronics unattended, or run machines unattended due to the risk of fire and malfunction.
9) Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. Just in case these fail. test your workshop smoke detector.
Product Specification:
1) Marlin firmware update: Arduino IDE 1.5.X
2) This kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD. It can control up to 5 stepper motors with 1/16 stepping precision and interface
5. BIQU A4988 Compatible StepStick Stepper Motor Diver Module with Heat Sink for 3D Printer Controller Ramps 1.4(Pack of 5pcs)
Feature
A4988 driver board widely used in 3D printers and small CNC machinesSimple step and direction control interface
Thermal protection, over-current protection, ground fault protection
Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage toachieve higher step rates
Description
Specifications:
Size:
A4988:20*15*11mm(LWH)
Heat Sink: 9*9*5mm(LWH)
Weight: 0.8ounces
Color: Red
Features:
-Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
-Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
-Automatic current decay mode detection / selection
-Internal UVLO
-Mixed with slow current decay modes
-Synchronous rectification for low power dissipation
-Crossover-current protection
-Thermal shutdown circuitry
-3.3 and 5 V compatible logic supply
-Thermal shutdown circuitry
-Ground Fault Circuit
-Load short-circuit protection
-Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16
Package Included:
5*A4988 StepStick Stepper Motor Diver Module
5*Heat Sink
6. Longruner 3D Printer Kit RAMPS 1.4 Controller Board + 5pcs A4988 StepStick Stepper Motor Driver Module + Heat Sink for 3D Printer Reprap, CNC Machine or Robotics
Feature
Flexible: 1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.RAMPS 1.4 expansion board as a driver expansion board, can be used for engraving machines, 3D printers and it is a total of five slots, can drive five A4988 stepper motor.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 * SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety Each road stepper motors only need two IO ports.
Stepper motor wiring as follows: 2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.
Using This suite (1pcs RAMPS 1.4 Controller Board+ 5pcs A4988 Stepstick Stepper Motor Driver Module with Heat Sink on your Arduino-compatible MEGA shield for easy service,part replacement,upgrade-ability and expansion.
Description
RAMPS 1.4 Controller BoardUpdate High Quality Ramp Board by changing MOSFET:
Old MOSFET IC Model : PDF55N06; Specification: VDSS: 60V; ID:55A
New MOSFET IC model: HM60N06; Specification: VDSS: 60V; ID: 60A
HM60N06 current up to 60A,More safety
Expandable to control other accessories.
3 Mosfets for heater / fan outputs and 3 thermistor circuits.
Fused at 5A for additional safety and component protection
Heated bed control with additional 11A fuse.
Fits 5 Pololu stepper driver boards.
Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs.
I2C and SPI pins left available for future expansion.
All the Mosfets are hooked into PWM pins for versatility.
Servo style connectors are used to connect to the end stops, motors, and LEDs. These connectors are rated for 3A, very compact, and globally available.
SD Card add on available.
LEDs indicate when heater outputs on.
Option to connect 2 motors to Z for Prusa Mendel.
A4988:
Simple step and direction control interface.
Can interface directly with 3.3 V and 5 V systems.
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout.
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use
voltages above your stepper motor's rated voltage to achieve higher step rates.
Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
45 V maximum supply voltage.
Built-in regulator.(no external logic voltage supply needed)
Package include:
1 * RAMPS 1.4 controller board
5 * A4988 Step stick Driver
5 * Heat Sink
7. KINGPRINT MKS-Gen V1.4 Controller Board+5PCS DRV8825 Stepper Motor Mega 2560 Motherboard RepRap Ramps1.4 Compatible +USB Cable for 3D Printer
Feature
The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.
The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
Description
Specification: Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )MEGA2560 and RAMPS 1.4 set on a board, to solve complicated RAMPS1.4 combination of interfaces, the problem of failure prone.
Support up to 5 motor driver (A4988 or DRV8825).
Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
Package Included:
5 * DRV8825S Stepper Motor Driver
1 * MKS-Gen V1.4 Controller Board
1 * USB Cable
5 * Mini Heat Sink
8. BIQU A4988 Compatible StepStick Stepper Motor Diver Module with Heat Sink for 3D Printer Controller Ramps 1.4(Pack of 5pcs)
Feature
A4988 driver board widely used in 3D printers and small CNC machinesSimple step and direction control interface
Thermal protection, over-current protection, ground fault protection
Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage toachieve higher step rates
Description
Specifications:
Size:
A4988:20*15*11mm(LWH)
Heat Sink: 9*9*5mm(LWH)
Weight: 0.8ounces
Color: Green
Features:
-Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
-Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
-Automatic current decay mode detection / selection
-Internal UVLO
-Mixed with slow current decay modes
-Synchronous rectification for low power dissipation
-Crossover-current protection
-Thermal shutdown circuitry
-3.3 and 5 V compatible logic supply
-Thermal shutdown circuitry
-Ground Fault Circuit
-Load short-circuit protection
-Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16
Package Included:
5*A4988 StepStick Stepper Motor Diver Module
5*Heat Sink
9. KINGPRINT DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer Rrerap Ramps 1.4 A4988 (Pack of 5pcs)
Feature
-The module has a pinout, it can be used as a better performance of the pull-down menu board replacement in many applications-DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step)
-It uses 8.2 - 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling)
-Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay)
-Built-in voltage regulator (the need for any external logic supply voltage)
Description
1.A simple steps and direction control interface2.Six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step
3.CAN interface directly with 3.3 V and 5 V systems
4.Over-temperature thermal shutdown, overcurrent shutdown, undervoltage lockout
5.Short to ground short circuit load protection
6.4 Layer 2 oz copper PCB, in order to improve heat dissipation
7.Exposed solder ground below the bottom of the driver IC on the printed circuit board pad
8.Module size, pin and interface matching A4988 stepper motor driver operators in many ways
9.Adjustable current control lets you set a potentiometer, which lets you use the stepper motor's rated voltage or more, in order to achieve a higher rate of maximum output current step
10.Maximum 45 V supply voltage
Package Included:
5* DRV8825 Stepper Motor Driver Module
5*Heat Sink
More Item:
KINGPRINT TMC2130/TMC2208 Stepper Motor Driver
NOTE:
If you find any problem, please contact us at first, and our technical staff will help you to solve the problem at once. Thanks!
10. kuman 3D Printer Controller Kit for Arduino Mega 2560 Uno R3 Starter Kits +RAMPS 1.4 + 5pcs A4988 Stepper Motor Driver + LCD 12864 for Arduino Reprap K17
Feature
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety3D Printer Controller RAMPS 1.4,A4988 Stepper Motor Driver
LCD 12864 Graphic Smart Display Controller
3D Printer Controller 100% compatible with Arduino RepRap
Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents
Description
Product Specs:(1) Mega 2560 R3
(2) 3D Printer Controller RAMPS 1.4 It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included.
Update High Quality Ramp Board by changing MOSFET: old MOSFET IC Model : PDF55N06 SpecificationVDSS:60V ID:55A New MOSFET IC model: HM60N06 SpecificationVDSS:60V ID:60A HM60N06 current up to 60AMore safety
Package List:
(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) Cable x 2
(7) USB Cable x 1
Detailed tutorials including project introduction and source code CAN BE PROVIDED FOR FREE,contact us BY Email to get documents.
Note:
1. You just need to connect the computer with Mega 2560 via USB download cable when burning firmware.
2.The chip and circuit may be burnt when the power and motor driver board reversed, so please confirm twice before powering.
3.You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.
