Finding the best macbook air rubber feet suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best macbook air rubber feet
1. UESWILL 4 Pcs Replacement Bottom Case White Rubber Feet Foot for UESWILL MacBook Case/ Macbook Pro Case / MacBook Air Case Cover
Feature
Replacement White Rubber Feet 4 Pcs.Please clean the hole of the feet on the MacBook Case before attaching the rubber feet.
Diameter: 1.5 CM / 0.6 inch
2. Generic OEM Bottom Case Rubber Feet for MacBook Air 13 inch A1369 A1466 2010 2011 2012 2013
Feature
Color:BlackMaterial: Rubber&Plastic (a little harder than original one)
Includ: 4XOuter foot +1X bottom case screw + 1Xsuper glue + 1Xscrewdriver
Fit for all MacBook Air 13 inch A1369 A1466,(NOT FOR 11 inch A1370 A1465 )
Description
Warning:
1.Do not wipe the glue.use the cotton dry swab to absorb any excess glue.
2.Fumes from other types of glue could affect other internal components.Excess puddled glue may take hours to dry and may cause the bottom case to adhere to the logic board or interior cabling.
3.Screws at sides and front must be removed and installed at an angle.
4.Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface.
SAFETY INSTRUCTIONS-GLUE IS AN EYE AND SKIN IRRITANT.
GLUE BONDS TO SKIN INSTANTLY.
Contains ethyl cyanoacrylate. Avoid contact with skin and eyes. If eye or mouth contact occurs, hold eyelid or mouth open and rinse thoroughly but gently with water only for 15 minutes and GET MEDICAL ATTENTION. Liquid glue will sting eye temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by an eye doctor.
If skin bonding occurs, soak in acetone-based nail polish remover or warm soapy water and carefully peel or roll skin apart (do not pull). Contact through clothing may cause skin burn. If spilled on clothing, flush with cold water. Avoid prolonged breathing of vapors. use with adequate ventilation. KEEP OUT OF THE REACH OF CHILDREN.
General Information
1.A MacBook Pro covered by the Apple Limited Warranty or by an AppleCare Protection Plan may receive a replacement foot without charge.
2.A MacBook Pro that is out-of-warranty may have a charge associated with the replacement.
3.The DIY replacement kit not available for MacBook Pro OR Pro with Retina display computers.
4.Material
This set is not original. Please note it is harder than original one.
5.How to replace
https://support.apple.com/en-us/HT202450
3. BisLinks 4 X Bottom Base Rubber Plastic Feet For MacBook Air 11" 13" A1369 1466 1370 1465
Feature
Brand: BisLinksCompatible Brand: For Apple
Model: Macbook Air
Colour: Black
Supplied: 4 x Bottom Plastic Rubber Feet
Description
This is an OEM bottom base case plastic rubber foot feet perfect replacement part for your Apple MacBook Air 11" 13" A1369 A1466 A1370 A1465. If you have broken, sticky, lost or damage bottom base case rubber feet which is already lost then you will need this brand new bottom base case plastic rubber foot. Don't hesitate to give your device a new look for better experience. This part is guaranteed to function as long as you have it.Technical Information: -
Compatible with Apple MacBook Air 11" 13" A1369 A1466 A1370 A1465.
Perfect OEM replacement part for faulty/broken/damage or lost bottom base case plastic rubber foot.
Perfect fitting & functionality of OEM parts is guaranteed.
High quality OEM part replacement
Comes ready to install.
Includes: -
4 x Bottom Plastic Rubber Feet
Important Note: -
Opening your Device will void your Warranty; BisLinks cannot be held responsible for any damage occurred during your repair process. Please feel free to contact us for further information.
4. Generic OEM Bottom Case Rubber Feet for MacBook Air A1370 A1369 A1466 A1465
Feature
For MBA 13.3 inch 11.6 inch MBA Macbook air rubber feet pad set include 4pcs out feet , super glue and screwdriver. Anti-slip Rubber feet is used for supporting the whole MBA, with 3m self adhesive sticker. The adhesive pasted on macbook air rubber feet, is one kind of two sided sticky tape that comes off easily, super glue is necessary to stick them tightly. Macbook air foot-out feet is made of rubber,but the out feet is a little harder than original.There are 3 types of macbook rubber feet, check serious No. at the bottom case before order. This kind of rubber feet are fit for AIR ONES( A1370 A1369 A1465 A1466 ) ONLY ,not for macbook PRO mac 13 mac 15 mac 17 A1278 A1286 A1297 PRO RETINA ONES(A1425 A1502 A1398)
Includ: Macbook Air feet 4, glue 1, screwdriver 1
Material: Rubber&Plastic (a little harder than original one)
Convenience Packaging with tools, Easy replacement with Instruction
Description
Warning:
1.Do not wipe the glue.use the cotton dry swab to absorb any excess glue. Fumes from other types of glue could affect other internal components.Excess puddled glue may take hours to dry and may cause the bottom case to adhere to the logic board or interior cabling.
2.Screws at sides and front must be removed and installed at an angle.
3.Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface.
SAFETY INSTRUCTIONS-GLUE IS AN EYE AND SKIN IRRITANT.
GLUE BONDS TO SKIN INSTANTLY.
Contains ethyl cyanoacrylate. Avoid contact with skin and eyes. If eye or mouth contact occurs, hold eyelid or mouth open and rinse thoroughly but gently with water only for 15 minutes and GET MEDICAL ATTENTION. Liquid glue will sting eye temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by an eye doctor.
If skin bonding occurs, soak in acetone-based nail polish remover or warm soapy water and carefully peel or roll skin apart (do not pull). Contact through clothing may cause skin burn. If spilled on clothing, flush with cold water. Avoid prolonged breathing of vapors. use with adequate ventilation. KEEP OUT OF THE REACH OF CHILDREN.
General information
1.A MacBook Pro covered by the Apple Limited Warranty or by an AppleCare Protection Plan may receive a replacement foot without charge.
2.A MacBook Pro that is out-of-warranty may have a charge associated with the replacement.
3.The DIY replacement kit not available for MacBook Pro OR Pro with Retina display computers.
4.How to replace
https://support.apple.com/en-us/HT202450
5. eBoot 4 Pack Rubber Case Feet with Screws Screwdriver Kit Set for Apple MacBook Pro A1278 A1286 A1297 13 15 17 (Not for Retina Display)
Feature
Suitable for macbook pro Unibody A1278 A1286 A1297 (not for retina display)Can be applied for macbook pro in 13 inches, 15 inches and 17 inches (not for retina display)
Screwdriver measures 3.3 inches
Case foot is made of rubber and plastic, durable
Package includes: 10 * bottom screws, 4 * bottom out foot, 1 * screwdriver
Description
Applicable models:
Macbook pro 13" A1278 2009 2010 2011 2012
Macbook pro 15" A1286 2009 2010 2011 2012
Macbook pro 17" A1297 2009 2010 2011
Note:
Not for macbook pro retina series.
Package includes:
10 * Bottom screws
4 * Bottom out foot
1 * Screwdriver
Foot installation method:
1.Using the screwdriver, separate the bottom case by removing the 10 screws.
2.Clean the bottom with a dry cloth, make sure that the foot area on the bottom case is clean and free of debris.
3.You can install foot directly, however, in order to keep the foot fixed better, you can use heating tool (such as hair dryer) to heat the foot area on back of bottom case, and then put on rubber foot when the foot area is hot.
4.Please keep pressing the rubber foot until the foot area cools down.
5.After the heating place cooling down, clean and install the bottom case.
6. Generic OEM Bottom Case Rubber Feet for MacBook Air 11 inch A1370 A1465 2010 2011 2012 2013
Feature
Color:BlackMaterial: Rubber&Plastic (a little harder than original one)
Includ: 4XOuter foot + bottom case screw + super glue + screw driver
Fit for all MacBook Air 11 inch A1370 A1465,(NOT FOR 13 inch A1369 A1466 )
Description
Warning:
1.Do not wipe the glue.use the cotton dry swab to absorb any excess glue.
2.Fumes from other types of glue could affect other internal components.Excess puddled glue may take hours to dry and may cause the bottom case to adhere to the logic board or interior cabling.
3.Screws at sides and front must be removed and installed at an angle.
4.Install screws in order shown. If sequence is not followed, bottom case might wobble when placed on level surface.
SAFETY INSTRUCTIONS-GLUE IS AN EYE AND SKIN IRRITANT.
GLUE BONDS TO SKIN INSTANTLY.
Contains ethyl cyanoacrylate. Avoid contact with skin and eyes. If eye or mouth contact occurs, hold eyelid or mouth open and rinse thoroughly but gently with water only for 15 minutes and GET MEDICAL ATTENTION. Liquid glue will sting eye temporarily. Solidified glue may irritate eye like a grain of sand and should be treated by an eye doctor.
If skin bonding occurs, soak in acetone-based nail polish remover or warm soapy water and carefully peel or roll skin apart (do not pull). Contact through clothing may cause skin burn. If spilled on clothing, flush with cold water. Avoid prolonged breathing of vapors. use with adequate ventilation. KEEP OUT OF THE REACH OF CHILDREN.
General Information
1.A MacBook Pro covered by the Apple Limited Warranty or by an AppleCare Protection Plan may receive a replacement foot without charge.
2.A MacBook Pro that is out-of-warranty may have a charge associated with the replacement.
3.The DIY replacement kit not available for MacBook Pro OR Pro with Retina display computers.
4.Material
This set is not original. Please note it is harder than original one.
5.How to replace
https://support.apple.com/en-us/HT202450
7. LENTION Hard Case for MacBook Air (11-inch, Late 2010 to Early 2015) - Model A1370 / A1465, with Keyboard Cover and Port Plugs, Matte Finish Case with Rubber Feet (Frost Black)
Feature
Only fits MacBook Air (11-inch, 2015/2014/2013/2012/2011/2010) - A1370/A1465. No Cut Out design, transparency is different from color to colorIncluding keyboard cover and port plugs to protect your Mac against dusts and contaminates. Highly recommend, extremely useful
Made of sturdy plastic that protects your Mac from scratches and striking. Micro clips on the case for easy installation & removal
The bottom case has 4 black rubber feet, same color as Mac's, much better than the easily wear-away white foam feet
Come with LENTION 1 year warranty on case, keyboard cover and port plugs and LENTION lifetime after-sales services
Description
LENTION Soft-Touch Series Hard CaseFeatures
* Keyboard cover and port plugs, keep dusts throughly away
* Soft rubber feet free the Mac from sliding and striking
* Snap-on design, minimal weight while providing excellent protection
* Easy installation, allows full access to all laptop ports
* Apple's Logo shine through the case
Please Check Your MacBook Model "A1xxx" before Purchase:
1) Turn your MacBook upside down.
2) Underneath, locate the Model Number in small print.
This SIZE is designed for MacBook Air 11-inch, Model A1370 / A1465
-- MacBook Air (11-inch, Early 2015)
-- MacBook Air (11-inch, Early 2014)
-- MacBook Air (11-inch, Mid 2013)
-- MacBook Air (11-inch, Mid 2012)
-- MacBook Air (11-inch, Mid 2011)
-- MacBook Air (11-inch, Late 2010)
8. UBatteries Compatible Laptop Bottom Case Rubber Feet Replacement For Apple MacBook Air A1370 A1406 A1465 A1237 A1245 A1304 A1369 A1377 A1405 A1466 A1496 MCPMIS-01
Feature
UBatteries Laptop Bottom Case Rubber Feet for Apple MacBook Air A1370 A1406 A1465 A1237 A1245 A1304 A1369 A1377 A1405 A1466 A1496 Series3 Month Warranty, 30 Days Return
CE ROHS Certified
For all MacBook Air models
Description
UBatteries Compatible Laptop Bottom Case Rubber Feet Replacement For Apple MacBook Air A1370 A1406 A1465 A1237 A1245 A1304 A1369 A1377 A1405 A1466 A1496 MCPMIS-0130 day worry free/no question ask return policy
Compatible Models: All MacBook Air Models
Compatible Part Numbers: A1370 A1406 A1465 A1237 A1245 A1304 A1369 A1377 A1405 A1466 A1496
UBatteries LLC is the manufacturer and exclusive distributer of UBatteries & UB products,
any other products listed or sold under our branded name are not GENUINE
or protected by our warranty. Any attempt to copy, relist or resell of UBatteries products without
permission is prohibited, we reserve the right to take action against violators.
Copy Right UBatteries LLC 2015
9. iLeadon MacBook Air 13 inch Protective Hard Case Rubber Coated Ultra Thin Shell Cover+Keyboard Cover for MacBook Air 13 inch Model A1369/A1466 (MacBook Air 13", Blue Marble)
Feature
This case Only fit for Apple Macbook Air 13 inch Model A1369 and A1466.Please kindly check model number on the bottom of your macbook before you place order. NOTE: This case is NOT compatible with 2018 New version Macbook Air 13 inch Model A1932 with Retina Display & Touch ID.Protect your Macbook in style with this Art Print Ultra Slim Rubberized durable plastic shell.
Bottom shell vented for maximum heat dissipation lightweight, two-piece, snap-on case includes four support feet.
Simple clip-on/off design without the added risk of harming your laptop during application.Plug your charger, cable or headset without removing the case.
Package include top and bottom case,4 pieces anti-skid rubberized feet,keyboard cover.
Description
iLeadon macbook case can protect your Macbook in style and Shock-proof/Drop resistance.Exclusive Designed For Macbook Air 13 inch Model A1466/A1369.The Ultra Thin Designed make your laptop portative with 360 Degree protection.The case was made by Eco-friendly material.
How to install Hard shell Case.
Two clips on top,Two clips on the bottom
1.Clear your Macbook to remove the surface dust before installing the case.
2.Place your Macbook into bottom case and press all tabs until secure.
3.Install the top case with Macbook half open and the Apple logo facing you,and snap on all tabs until secure.
How to remove Hardshell Case
Remove the bottom cover with laptop half open and the air fans facing towards you,and then pull the hook away from the corner,One side at a time.
10. MMOBIEL 4 x Rubber Case Feet pad Set with 10 x Bottom Base Screws (2 Long and 8 Short) and Philips Screwdriver Kit Set for MacBook Air A1370 A1369 A1465 A1466 11 and 13 inch incl. Cleaning Cloth
Feature
HIGH QUALITY PROFESSIONAL REPLACEMENT KIT: Suitable for Macbook AIR 11, 13 inch A1370 A1369 A1465 A1466COMPATIBILITY: Can be applied for Macbook Air in 11 and 13 Inches, There are 3 types of Macbook rubber Case feet pad, check serie No. at the bottom case before order
EASY INSTALLATION: Incl Screwdriver Philips measures 3.3 inches
PACKAGE INCLUDES: Top quality Metal 10 xbottom Base Screws, 2 x long and 8 x Short, including Thread locking cement 4 x Durable Anti slip bottom Rubber/plastic Case feet Outer foot, 1 x screwdriver
HIGH QUALITY: All Items are tested before shipping. Item in Stock Shipped from USA
